{"id":5483,"date":"2026-11-20T17:12:06","date_gmt":"2026-11-20T09:12:06","guid":{"rendered":"https:\/\/grandpackmachine.com\/?p=5483"},"modified":"2026-11-20T17:12:06","modified_gmt":"2026-11-20T09:12:06","slug":"face-seal-blister-packaging","status":"publish","type":"post","link":"https:\/\/grandpackmachine.com\/ru\/face-seal-blister-packaging\/","title":{"rendered":"How to Test Face Seal Blister Packaging Before Ordering Tooling"},"content":{"rendered":"<section class=\"grand-5483-quick-answer\" id=\"quick-answer\" aria-label=\"Quick Answer\">\n<p><strong>\u041a\u0440\u0430\u0442\u043a\u0438\u0439 \u043e\u0442\u0432\u0435\u0442:<\/strong> Before ordering production tooling for <strong>face seal blister packaging<\/strong>, test the actual printed and coated card with the formed plastic shell and real product. The trial must show that the flange sits on the intended seal land, the bond is continuous, the card remains acceptable and the package passes the buyer&#8217;s agreed opening check. Document the exact material and drawing revisions, sample count, machine conditions and results. Approve only the configuration supported by that record.<\/p>\n<\/section>\n<p class=\"grand-5483-scope-note\">This guide addresses pre-tooling testing of retail paperboard-and-plastic face seals. It is not a substitute for qualification of pharmaceutical foil-lidded blister packaging or verification with the final production tool.<\/p>\n<nav class=\"grand-5483-toc\" aria-label=\"Article contents\">\n<div class=\"grand-5483-toc-title\">In This Article<\/div>\n<ol>\n<li><a href=\"#how-the-blister-flange-seals-to-the-card\"><span class=\"grand-5483-toc-num\" aria-hidden=\"true\">01<\/span><span class=\"grand-5483-toc-label\">Identify the Face-Seal Joint<\/span><\/a><\/li>\n<li><a href=\"#what-to-bring-to-the-sealing-trial\"><span class=\"grand-5483-toc-num\" aria-hidden=\"true\">02<\/span><span class=\"grand-5483-toc-label\">Prepare the Trial Kit<\/span><\/a><\/li>\n<li><a href=\"#what-to-inspect-on-the-first-sealed-samples\"><span class=\"grand-5483-toc-num\" aria-hidden=\"true\">03<\/span><span class=\"grand-5483-toc-label\">Inspect the Sealed Samples<\/span><\/a><\/li>\n<li><a href=\"#what-to-approve-before-ordering-tooling\"><span class=\"grand-5483-toc-num\" aria-hidden=\"true\">04<\/span><span class=\"grand-5483-toc-label\">Make the Tooling Decision<\/span><\/a><\/li>\n<li><a href=\"#frequently-asked-questions-about-face-seal-trials\"><span class=\"grand-5483-toc-num\" aria-hidden=\"true\">05<\/span><span class=\"grand-5483-toc-label\">Questions Before Approval<\/span><\/a><\/li>\n<\/ol>\n<\/nav>\n<h2 id=\"how-the-blister-flange-seals-to-the-card\">1. Identify the Face-Seal Joint<\/h2>\n<p>Start with three items on the workbench: the intended printed card, the formed clear blister shell and the actual product. The thermoformed cavity holds the product; the shell&#8217;s flat peripheral <strong>flange<\/strong> meets the heat-sealable coating on the card face. That flange-to-card contact path is the joint the trial must examine\u2014not the raised cavity.<\/p>\n<p>Position the shell on the printed card and trace the entire sealing path. Confirm which side has the heat-seal coating, whether the flange overlaps the intended coated area and whether cutouts, hang holes or artwork leave enough clearance. A trapped-card blister instead holds the flange between two paperboard layers; it is a different structure. See the GRAND guide to <a href=\"https:\/\/grandpackmachine.com\/ru\/types-of-blister-packaging\/\">types of blister packaging<\/a> for the comparison.<\/p>\n<p class=\"grand-5483-figure-label\"><strong>Face-Seal Blister Joint \u2014 Technical Illustration<\/strong><\/p>\n<figure class=\"grand-5483-cross-section grand-5483-photo-cutaway\" role=\"group\" aria-label=\"Detailed illustrative cross-section of face-seal blister packaging\" style=\"max-width:480px;overflow:hidden;margin:18px auto 25px;\">\n<img src=\"https:\/\/grandpackmachine.com\/wp-content\/uploads\/2026\/11\/grand-face-seal-blister-structure-technical-cutaway-1120.webp\" width=\"1120\" height=\"840\" loading=\"lazy\" decoding=\"async\" alt=\"Detailed engineering rendering of a transparent thermoformed blister cavity and peripheral plastic flange bonding to the heat-seal coating on a printed paperboard retail card\" style=\"width:100%;height:auto;display:block;border:1px solid #dce7f0;border-radius:8px;box-sizing:border-box;\" \/><br \/>\n<\/figure>\n<p>The visible appearance of a seal is only the first check. The buyer and supplier must also agree how opening or separation will be evaluated. The general face-seal construction is described in <a href=\"https:\/\/www.rohrer.com\/blog\/blister-packaging-101\/\" rel=\"nofollow noopener noreferrer\" target=\"_blank\">Rohrer&#8217;s blister packaging overview<\/a>.<\/p>\n<h2 id=\"what-to-bring-to-the-sealing-trial\">2. Prepare the Actual Trial Kit and Acceptance Plan<\/h2>\n<p>\u0418\u0441\u043f\u043e\u043b\u044c\u0437\u043e\u0432\u0430\u0442\u044c <strong>production-intent materials<\/strong>, not interchangeable-looking substitutes. At the supplier&#8217;s bench, the test set should be traceable to the card, shell, product and trial fixture you expect to approve. Agree on the sample count, observation locations and acceptance criteria before the first seal.<\/p>\n<p class=\"grand-5483-table-label\"><strong>Table 1. What to Bring and Why It Matters<\/strong><\/p>\n<div class=\"grand-5483-table-scroll\" role=\"region\" aria-label=\"Production-intent trial kit inputs and reasons\" tabindex=\"0\">\n<table>\n<thead>\n<tr>\n<th scope=\"col\">Trial input<\/th>\n<th scope=\"col\">Specification \/ evidence to bring<\/th>\n<th scope=\"col\">Why this matters<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Printed paperboard card<\/td>\n<td>Actual printed stock and lot, cut dieline, artwork revision, heat-seal coating identity and coated face.<\/td>\n<td>A plain card or a different coating does not establish approval of the final printed pack.<\/td>\n<\/tr>\n<tr>\n<td>Formed plastic shell<\/td>\n<td>Actual thermoformed material and lot, shell revision, flange outline, flatness and intended registration features.<\/td>\n<td>The flange must sit on the intended seal-coated land all around the cavity.<\/td>\n<\/tr>\n<tr>\n<td>Real product sample<\/td>\n<td>Representative product dimensions, cavity orientation, seating and any features affecting the shell or support.<\/td>\n<td>A substitute product can hide a seating or fixture problem.<\/td>\n<\/tr>\n<tr>\n<td>Trial fixture and setup<\/td>\n<td>Machine\/test-sealer identity, nest and locating features, heating tool\/platen, and fixture revision.<\/td>\n<td>The test setup must be traceable if alignment or pressure\/contact is questioned.<\/td>\n<\/tr>\n<tr>\n<td>Buyer acceptance plan<\/td>\n<td>Agreed number and location of samples; visual, opening and separation methods; criteria and inspection responsibilities.<\/td>\n<td>Do not declare a pass when criteria, method or sample plan are missing.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<p class=\"grand-5483-table-hint\">On a smaller screen, scroll the table horizontally to read all columns.<\/p>\n<p>A supplier may use an unprinted card, a different blister batch or an interim fixture to screen feasibility. Record that scope clearly: it is <strong>\u043d\u0435\u0442<\/strong> automatic approval of a different production combination.<\/p>\n<p>Define what each equipment reading represents. Record the actual <strong>temperature setpoint<\/strong>, any separately measured temperature, <strong>force or pressure<\/strong>, \u0438 <strong>dwell time<\/strong>, with their units. A heater setpoint is not necessarily the temperature at the sealing interface, and an air-pressure reading is not necessarily the force at the flange.<\/p>\n<p>GRAND&#8217;s <a href=\"https:\/\/grandpackmachine.com\/ru\/grand-ac-350-blister-card-packaging-machine\/\">AC-350 blister card packaging overview<\/a> is useful for understanding the forming, card-positioning and sealing workflow. It does not establish that this particular project uses the AC-350 or its settings; the trial machine and separately formed versus integrated shell supply must be confirmed.<\/p>\n<h2 id=\"what-to-inspect-on-the-first-sealed-samples\">3. Inspect the First Sealed Samples in a Fixed Order<\/h2>\n<p>Inspect the agreed number of samples in the same sequence. The important distinction is between <strong>what the sample shows<\/strong> \u0438 <strong>what might have caused it<\/strong>. Do not change machine settings merely because a defect is visible.<\/p>\n<p class=\"grand-5483-table-label\"><strong>Table 2. Trial Inspection Checklist and Required Evidence<\/strong><\/p>\n<div class=\"grand-5483-table-scroll\" role=\"region\" aria-label=\"Face seal trial checkpoints and evidence\" tabindex=\"0\">\n<table>\n<thead>\n<tr>\n<th scope=\"col\">Checkpoint<\/th>\n<th scope=\"col\">What to inspect<\/th>\n<th scope=\"col\">Evidence and next investigation<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Card and shell registration<\/td>\n<td>Compare the shell and flange location with the approved card dieline and coated area.<\/td>\n<td>Document direction and location of offsets; check the nest, print and locating datum.<\/td>\n<\/tr>\n<tr>\n<td>Flange contact and seating<\/td>\n<td>Inspect the flange and corners for rocking, twisting, incomplete seating or gaps at the contact path.<\/td>\n<td>Mark the affected side\/corner; examine shell flatness and tool\/nest support.<\/td>\n<\/tr>\n<tr>\n<td>Seal continuity<\/td>\n<td>Follow the full flange contact path for unbonded sections, lifted edges and repeatable openings.<\/td>\n<td>Mark and photograph any open position; visual continuity alone is not an opening test.<\/td>\n<\/tr>\n<tr>\n<td>Card and printed surface<\/td>\n<td>Look for warp, curl, crease, surface scuffing, coating damage or distortion.<\/td>\n<td>Record the affected face\/location and consider material, contact and dwell conditions.<\/td>\n<\/tr>\n<tr>\n<td>Opening or separation check<\/td>\n<td>Perform the buyer-agreed method and observe the location\/type of separation. Quantitative testing needs the agreed method and units.<\/td>\n<td>Record measured result when required; do not assume a universal peel-force acceptance threshold.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<p class=\"grand-5483-table-hint\">These are inspection prompts, not universal numeric acceptance values. Apply the buyer&#8217;s signed criteria.<\/p>\n<p>Where the buyer requires a quantitative separation result, identify the test method, units, sampling locations and observed failure position. The <a href=\"https:\/\/fogra.org\/en\/testing\/packaging-print-finishing\/packagings\" rel=\"nofollow noopener noreferrer\" target=\"_blank\">Fogra packaging-testing guidance<\/a> supports testing actual materials across temperature, pressure and time combinations and observing separation behavior; it does not provide a project-specific pass threshold.<\/p>\n<h3 id=\"why-does-a-corner-repeatedly-lift-after-sealing\">Worked Example: A Repeatedly Lifted Upper-Right Corner<\/h3>\n<p><strong>Hypothetical scenario, not a recorded customer test:<\/strong> Several packs lift at the same upper-right corner. First label that location on the trial photos and check whether the blister is offset relative to the card or coated area. Next inspect the shell flange and nest contact in that corner. If registration and contact are consistent, review the material and coating specification and then the recorded sealing conditions. Change one suspected cause under comparable conditions and repeat the agreed checks. A corrected-looking corner is not sufficient unless the required opening result is also acceptable.<\/p>\n<h2 id=\"what-to-approve-before-ordering-tooling\">4. Decide Whether Production Tooling Can Be Ordered<\/h2>\n<p>The pre-tooling trial should end with a <strong>documented decision about one defined card-and-shell configuration<\/strong>. The result belongs to the tested revisions and conditions; it should not be generalized to other coatings, shells or production tooling.<\/p>\n<section class=\"grand-5483-flow\" aria-label=\"From sample trial to tooling decision\">\n<p class=\"grand-5483-flow-heading\"><strong>From trial samples to a tooling decision<\/strong><\/p>\n<ol>\n<li><span class=\"grand-step\" aria-hidden=\"true\">01<\/span><span class=\"grand-step-copy\"><strong>Identify the approved materials<\/strong>Lock the card coating, plastic shell, product sample and drawings to specific revisions.<\/span><\/li>\n<li><span class=\"grand-step\" aria-hidden=\"true\">02<\/span><span class=\"grand-step-copy\"><strong>Record a controlled trial<\/strong>Agree the sample locations and count; log temperature, applied force or pressure and dwell time with units.<\/span><\/li>\n<li><span class=\"grand-step\" aria-hidden=\"true\">03<\/span><span class=\"grand-step-copy\"><strong>Inspect visual and opening evidence<\/strong>Compare registration, flange seating, continuous seal, printed-card condition and the agreed separation result.<\/span><\/li>\n<li><span class=\"grand-step\" aria-hidden=\"true\">04<\/span><span class=\"grand-step-copy\"><strong>Approve, correct\/retest, or revise<\/strong>Use the results for the tested configuration only, and document the responsible owner and next trial.<\/span><\/li>\n<\/ol>\n<\/section>\n<h3 id=\"three-possible-trial-dispositions\">Three possible trial decisions<\/h3>\n<ul>\n<li><strong>Approve the defined configuration for production-tooling design:<\/strong> The material and drawings match, the agreed inspected samples meet the appearance and opening criteria, and no unexplained opening or damage remains. Preserve the revisions and recorded results with the tooling request.<\/li>\n<li><strong>Correct the setup and repeat:<\/strong> Evidence points to card\/shell location, fixture contact or a controlled process variable, while the proposed materials still appear suitable. Assign the corrective action and compare like-for-like samples in a repeat trial.<\/li>\n<li><strong>Revise the material or drawing:<\/strong> The coating, plastic grade, flange profile, card dieline or other material feature does not match the intended package or the agreed criteria. Revise the controlled specification and treat the next trial as a new configuration.<\/li>\n<\/ul>\n<p><strong>Sample approval is not final production release.<\/strong> On the completed production tool, repeat appropriate checks using the final machine configuration and production-intent materials. Separately confirm the site&#8217;s requirements for sustained operation and any distribution testing.<\/p>\n<details class=\"grand-blister-faq grand-5483-blank-record\" style=\"margin-top:18px;\">\n<summary>Copy the nine-field blank trial record for your supplier visit<\/summary>\n<div class=\"grand-5483-faq-answer\">\n<p>Complete a separate record for each material revision and trial condition. The blanks below are intentionally unfilled until a real trial is conducted.<\/p>\n<div class=\"grand-5483-table-scroll\" role=\"region\" aria-label=\"Blank traceable face-seal trial record\" tabindex=\"0\">\n<table>\n<thead>\n<tr>\n<th scope=\"col\">Trial record field<\/th>\n<th scope=\"col\">What the engineer must document<\/th>\n<th scope=\"col\">Your run<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Sample ID, batch, and count<\/td>\n<td>Identify each test set and how many samples were checked.<\/td>\n<td>____<\/td>\n<\/tr>\n<tr>\n<td>Printed card revision, stock and seal coating<\/td>\n<td>Use the same lot\/revision identifiers as the material records.<\/td>\n<td>____<\/td>\n<\/tr>\n<tr>\n<td>Blister revision, material and flange drawing<\/td>\n<td>Record the actual plastic material and controlled drawing revision.<\/td>\n<td>____<\/td>\n<\/tr>\n<tr>\n<td>Product sample and fixture\/tool revision<\/td>\n<td>Identify the sample and installed trial nest or tooling.<\/td>\n<td>____<\/td>\n<\/tr>\n<tr>\n<td>Temperature, force\/pressure, dwell time and units<\/td>\n<td>Log the equipment&#8217;s actual displayed settings, their units and where readings came from.<\/td>\n<td>____<\/td>\n<\/tr>\n<tr>\n<td>Registration, contact and open-edge location<\/td>\n<td>Describe exactly where the flange contacts or lifts, with sample-position evidence.<\/td>\n<td>____<\/td>\n<\/tr>\n<tr>\n<td>Card distortion and print condition<\/td>\n<td>Record the affected side, appearance and severity against buyer criteria.<\/td>\n<td>____<\/td>\n<\/tr>\n<tr>\n<td>Opening\/separation method, criterion and result<\/td>\n<td>State the agreed method, units where applicable and actual sample result.<\/td>\n<td>____<\/td>\n<\/tr>\n<tr>\n<td>Decision, corrective action, owner and repeat trial<\/td>\n<td>Approve the specific revision, retest after a defined change, or return for redesign.<\/td>\n<td>____<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n<\/details>\n<h2 id=\"frequently-asked-questions-about-face-seal-trials\">5. Questions to Resolve Before Approval<\/h2>\n<details class=\"grand-blister-faq\">\n<summary>Does a successful trial with blank paperboard approve the printed production card?<\/summary>\n<div class=\"grand-5483-faq-answer\">\n<p>Not automatically. The printed stock, coating and surface finish must match the actual production intent. If the print or coating changes, record the difference and agree on repeat testing before carrying the approval forward.<\/p>\n<\/div>\n<\/details>\n<details class=\"grand-blister-faq\">\n<summary>What does repeatable lifting at the same corner suggest?<\/summary>\n<div class=\"grand-5483-faq-answer\">\n<p>It is evidence of a localized problem, not proof of a single cause. First mark the corner, compare card-to-shell registration, flange contact and nest support. When those are comparable, investigate coating coverage and sealing settings with a controlled repeat.<\/p>\n<\/div>\n<\/details>\n<details class=\"grand-blister-faq\">\n<summary>Can a sample fixture prove the final production tooling will work?<\/summary>\n<div class=\"grand-5483-faq-answer\">\n<p>No. Sample-fixture trials help screen material compatibility and sealing geometry. Contact, heating, cycle and registration may change on final tooling. Repeat the agreed checks on the actual machine and completed tooling before production approval.<\/p>\n<\/div>\n<\/details>\n<p>Changing the card layout as well as testing its seal? Read the related <a href=\"https:\/\/grandpackmachine.com\/ru\/blister-tooling-design-format-changes\/\">blister tooling design and format-change review<\/a> to identify other stations affected by the new design.<\/p>\n<section class=\"grand-5483-closing-cta\" aria-label=\"Discuss face seal blister trial\" style=\"border-top:1px solid #dce7f0;padding:16px 0 0;margin:28px 0 12px;\">\n<p><strong>Discuss your face-seal pre-tooling trial with GRAND.<\/strong> Send your card dieline, coated-stock specification, shell\/flange drawing, actual product samples and agreed inspection requirements. See the <a href=\"https:\/\/grandpackmachine.com\/ru\/pharmaceutical-packaging-machine\/blister-card-packaging\/\">DGX-380 blister card packaging machine<\/a> for equipment context; the applicable project configuration needs confirmation. <a href=\"#face-seal-inquiry\">Open the inquiry form on this page<\/a> to share your requirements.<\/p>\n<\/section>","protected":false},"excerpt":{"rendered":"<p>Test face seal blister packaging with the intended printed card, formed shell, and product samples. Inspect flange alignment, seal continuity, and card condition before ordering tooling.<\/p>","protected":false},"author":1,"featured_media":5493,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[37],"tags":[],"class_list":["post-5483","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-blister-packaging-machine-articles"],"_links":{"self":[{"href":"https:\/\/grandpackmachine.com\/ru\/wp-json\/wp\/v2\/posts\/5483","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/grandpackmachine.com\/ru\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/grandpackmachine.com\/ru\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/grandpackmachine.com\/ru\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/grandpackmachine.com\/ru\/wp-json\/wp\/v2\/comments?post=5483"}],"version-history":[{"count":6,"href":"https:\/\/grandpackmachine.com\/ru\/wp-json\/wp\/v2\/posts\/5483\/revisions"}],"predecessor-version":[{"id":5492,"href":"https:\/\/grandpackmachine.com\/ru\/wp-json\/wp\/v2\/posts\/5483\/revisions\/5492"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/grandpackmachine.com\/ru\/wp-json\/wp\/v2\/media\/5493"}],"wp:attachment":[{"href":"https:\/\/grandpackmachine.com\/ru\/wp-json\/wp\/v2\/media?parent=5483"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/grandpackmachine.com\/ru\/wp-json\/wp\/v2\/categories?post=5483"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/grandpackmachine.com\/ru\/wp-json\/wp\/v2\/tags?post=5483"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}